![]() |
Subwoofer ? |
Post Reply ![]() |
Page <1 234 |
Author | ||
Catcher10 ![]() Forum Senior Member ![]() ![]() VIP Member Joined: December 23 2009 Location: Emerald City Status: Offline Points: 17964 |
![]() ![]() ![]() ![]() ![]() |
|
Unnatural could also mean, your not used to hearing the full frequency of music. Remember in todays world of iPhones and ear buds and clinical sounding of CDs, we are not used to full range sounds anymore or what some call warm sounds.
|
||
![]() ![]() ![]() |
||
![]() |
||
Dark Ness ![]() Forum Senior Member ![]() ![]() Joined: May 21 2021 Location: Edge of Town Status: Offline Points: 246 |
![]() ![]() ![]() ![]() ![]() |
|
-5 dB
|
||
![]() |
||
Dark Ness ![]() Forum Senior Member ![]() ![]() Joined: May 21 2021 Location: Edge of Town Status: Offline Points: 246 |
![]() ![]() ![]() ![]() ![]() |
|
Precisely, we're on the same page (And that's what the sw is supposed to provide) what I mean by "unnatural" is not blending to the mix and standing out with a little too much reverb, if it's the correct expression, I'm lacking the right words maybe. (could this be related to the crossover setting you asked just a while ago?)
|
||
![]() |
||
Catcher10 ![]() Forum Senior Member ![]() ![]() VIP Member Joined: December 23 2009 Location: Emerald City Status: Offline Points: 17964 |
![]() ![]() ![]() ![]() ![]() |
|
Might be too loud.......What does the back panel show for volume and crossover? Could be the blend issue yes.
Edited by Catcher10 - March 17 2022 at 11:16 |
||
![]() ![]() ![]() |
||
![]() |
||
Catcher10 ![]() Forum Senior Member ![]() ![]() VIP Member Joined: December 23 2009 Location: Emerald City Status: Offline Points: 17964 |
![]() ![]() ![]() ![]() ![]() |
|
Yes, if you set the cross over too high your going to excite frequencies that don't need it, like 100Hz and higher, that's where the boominess will come from.
|
||
![]() ![]() ![]() |
||
![]() |
||
Dark Ness ![]() Forum Senior Member ![]() ![]() Joined: May 21 2021 Location: Edge of Town Status: Offline Points: 246 |
![]() ![]() ![]() ![]() ![]() |
|
^ I'll follow up your hint and get back with news soon.
|
||
![]() |
||
Dark Ness ![]() Forum Senior Member ![]() ![]() Joined: May 21 2021 Location: Edge of Town Status: Offline Points: 246 |
![]() ![]() ![]() ![]() ![]() |
|
SVS recommends for my LS the following settings : low pass filter 50 hz with a slope 24db/octave I'll try this and report soon, in the meantime I welcome any comment from the more experienced around. thanks guys |
||
![]() |
||
Catcher10 ![]() Forum Senior Member ![]() ![]() VIP Member Joined: December 23 2009 Location: Emerald City Status: Offline Points: 17964 |
![]() ![]() ![]() ![]() ![]() |
|
As mentioned, 50Hz should be your staring point considering your mains freq response. PM coming..... |
||
![]() ![]() ![]() |
||
![]() |
||
Dark Ness ![]() Forum Senior Member ![]() ![]() Joined: May 21 2021 Location: Edge of Town Status: Offline Points: 246 |
![]() ![]() ![]() ![]() ![]() |
|
^ You're right, you had already mentioned that setting and it works well. Coming next: the phase test/config routine... |
||
![]() |
||
Catcher10 ![]() Forum Senior Member ![]() ![]() VIP Member Joined: December 23 2009 Location: Emerald City Status: Offline Points: 17964 |
![]() ![]() ![]() ![]() ![]() |
|
![]() |
||
![]() ![]() ![]() |
||
![]() |
Post Reply ![]() |
Page <1 234 |
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |